Showing posts with label Concept cars. Show all posts
Showing posts with label Concept cars. Show all posts
Tuesday, May 31, 2011
Audi has revealed the A1 clubsport quattro, a one-off show car that will debut at the upcoming Wörtherseetour 2011.
Under the bonnet is the familiar 2.5 litre, five cylinder turbocharged motor from the TT RS and RS 3 Sportback, but output has been boosted by nearly 50% to 496 bhp (370 kW / 503 PS). Maximum torque is a substantial 660 Nm (486 lb/ft).
As expected, loads of power plus a small lightweight hatchback equals very rapid acceleration. The 0-62 mph (100 km/h) sprint is completed in 3.7 seconds, while the 50 - 75 mph (80 - 120 km/h) increment takes just 2.4 seconds in fourth gear. However, Audi wasn’t brave enough to ditch the speed limiter, so the A1 clubsport quattro won’t go beyond 155 mph (250 km/h).
It should be able to stop okay though, thanks to carbon fibre ceramic discs with six-piston calipers up front, paired with steel discs at the rear. Those brakes sit behind bespoke 19” alloy wheels that are shod with 255/30 section tyres.
Visually, there’s no mistaking the clubsport quattro. The front and rear wings have been widened by six centimetres, and the roof panel is made from carbon fibre reinforced polymer. A revised front valance incorporates larger air intakes, while the prominent double rear spoiler is there to ensure sufficient down force is generated.
On the inside, there’s a pair of leather-trimmed bucket seats borrowed from the R8 GT that come complete with four-point racing harnesses. In keeping with the stripped out racer look, the rear seats have been ditched altogether, as has the audio system. Even the door handles have disappeared, replaced by red fabric loops.
Related posts:
2011 What Car? Awards
Audi launches RS 3
Audi A1 1.4 TFSI, not S1
Audi has revealed the A1 clubsport quattro, a one-off show car that will debut at the upcoming Wörtherseetour 2011.
Under the bonnet is the familiar 2.5 litre, five cylinder turbocharged motor from the TT RS and RS 3 Sportback, but output has been boosted by nearly 50% to 496 bhp (370 kW / 503 PS). Maximum torque is a substantial 660 Nm (486 lb/ft).
As expected, loads of power plus a small lightweight hatchback equals very rapid acceleration. The 0-62 mph (100 km/h) sprint is completed in 3.7 seconds, while the 50 - 75 mph (80 - 120 km/h) increment takes just 2.4 seconds in fourth gear. However, Audi wasn’t brave enough to ditch the speed limiter, so the A1 clubsport quattro won’t go beyond 155 mph (250 km/h).
It should be able to stop okay though, thanks to carbon fibre ceramic discs with six-piston calipers up front, paired with steel discs at the rear. Those brakes sit behind bespoke 19” alloy wheels that are shod with 255/30 section tyres.
Visually, there’s no mistaking the clubsport quattro. The front and rear wings have been widened by six centimetres, and the roof panel is made from carbon fibre reinforced polymer. A revised front valance incorporates larger air intakes, while the prominent double rear spoiler is there to ensure sufficient down force is generated.
On the inside, there’s a pair of leather-trimmed bucket seats borrowed from the R8 GT that come complete with four-point racing harnesses. In keeping with the stripped out racer look, the rear seats have been ditched altogether, as has the audio system. Even the door handles have disappeared, replaced by red fabric loops.
Related posts:
2011 What Car? Awards
Audi launches RS 3
Audi A1 1.4 TFSI, not S1
Friday, May 20, 2011
Fifty years after the DB4GT Zagato, and following in the wheel tracks of several subsequent collaborations with the Italian design house, Aston Martin has unveiled the new V12 Zagato concept.
Its debut will be at the Villa D'Este Concours on 21st May 2011, which takes place near Lake Como in Italy. Aston Martin is going to use the occasion to ‘gauge customer interest’, despite already confirming that a strictly limited run of cars will be built.
But the V12 Zagato isn’t just going to be a road car. In the tradition of previous Aston Martin Zagatos a race programme is planned, starting off with the four hour VLN Nürburgring race on 28th May 2011, and then followed by a 24 hour event at the same venue on 25th and 26th June 2011.
Unsurprisingly for a Zagato creation, the looks are arguably more challenging than those of a series production Aston Martin.
Even Marek Reichman, Director of Design at Aston Martin, described it as ‘an elegant yet brutal design which reflects the great balance between race performance and pure Aston Martin style. The original DB4GT Zagato was a true icon, powerful and graceful; the new design is a true representation of the spirit of DB4GT Zagato. The muscular organic forms define the thoroughbred nature of the car's racing credentials.’
Regardless of whether the styling divides opinion, there’s no disputing the craftsmanship that has gone into building the car. Sitting atop the bonded aluminium structure (borrowed from the V12 Vantage) is a handmade aluminium body, assembled using traditional techniques. The front wings, for example, are each made from seven separate pieces of metal, while the roof panel alone uses five pieces.
No word on prices yet, but that probably won’t be of much concern to prospective owners.
| Aston Martin V12 Zagato (Endurance Race Specification) | |
|---|---|
| Body | |
| Type | Two door, two seat coupe |
| Chassis | Bonded aluminium structure |
| Body | Hand crafted aluminium |
| Roll cage | FIA compliant; steel |
| Fuel system | 120 litre endurance racing fuel tank |
| Suspension | All-round independent double wishbone with fully adjustable Multimatic DSSV dampers |
| Front brakes | Ventilated floating grooved discs with 6 piston callipers |
| Rear brakes | Ventilated floating grooved discs with 4 piston callipers |
| Engine | |
| Type | All alloy, quad overhead cam 48-valve 5,935 cc V12 |
| Location | Front mid-mounted |
| Power | 510 bhp (380 kW / 517 PS) |
| Torque | 570 Nm (420 lb/ft) |
| Compression ratio | 10.9:1 |
| Transmission | |
| Drive | Rear-wheel drive; limited slip differential; magnesium alloy torque tube with carbon fibre propeller shaft |
| Gearbox | Six-speed automated manual gearbox with auto shift manual / select shift manual (ASM / SSM) electric hydraulic control system; rear-mid mounted |
| Clutch | Twin plate competition |
Related posts:
Alfa Romeo TZ3 Stradale
Aston Martin is coolest
Alfa Romeo TZ3 Corsa
Fifty years after the DB4GT Zagato, and following in the wheel tracks of several subsequent collaborations with the Italian design house, Aston Martin has unveiled the new V12 Zagato concept.
Its debut will be at the Villa D'Este Concours on 21st May 2011, which takes place near Lake Como in Italy. Aston Martin is going to use the occasion to ‘gauge customer interest’, despite already confirming that a strictly limited run of cars will be built.
But the V12 Zagato isn’t just going to be a road car. In the tradition of previous Aston Martin Zagatos a race programme is planned, starting off with the four hour VLN Nürburgring race on 28th May 2011, and then followed by a 24 hour event at the same venue on 25th and 26th June 2011.
Unsurprisingly for a Zagato creation, the looks are arguably more challenging than those of a series production Aston Martin.
Even Marek Reichman, Director of Design at Aston Martin, described it as ‘an elegant yet brutal design which reflects the great balance between race performance and pure Aston Martin style. The original DB4GT Zagato was a true icon, powerful and graceful; the new design is a true representation of the spirit of DB4GT Zagato. The muscular organic forms define the thoroughbred nature of the car's racing credentials.’
Regardless of whether the styling divides opinion, there’s no disputing the craftsmanship that has gone into building the car. Sitting atop the bonded aluminium structure (borrowed from the V12 Vantage) is a handmade aluminium body, assembled using traditional techniques. The front wings, for example, are each made from seven separate pieces of metal, while the roof panel alone uses five pieces.
No word on prices yet, but that probably won’t be of much concern to prospective owners.
| Aston Martin V12 Zagato (Endurance Race Specification) | |
|---|---|
| Body | |
| Type | Two door, two seat coupe |
| Chassis | Bonded aluminium structure |
| Body | Hand crafted aluminium |
| Roll cage | FIA compliant; steel |
| Fuel system | 120 litre endurance racing fuel tank |
| Suspension | All-round independent double wishbone with fully adjustable Multimatic DSSV dampers |
| Front brakes | Ventilated floating grooved discs with 6 piston callipers |
| Rear brakes | Ventilated floating grooved discs with 4 piston callipers |
| Engine | |
| Type | All alloy, quad overhead cam 48-valve 5,935 cc V12 |
| Location | Front mid-mounted |
| Power | 510 bhp (380 kW / 517 PS) |
| Torque | 570 Nm (420 lb/ft) |
| Compression ratio | 10.9:1 |
| Transmission | |
| Drive | Rear-wheel drive; limited slip differential; magnesium alloy torque tube with carbon fibre propeller shaft |
| Gearbox | Six-speed automated manual gearbox with auto shift manual / select shift manual (ASM / SSM) electric hydraulic control system; rear-mid mounted |
| Clutch | Twin plate competition |
Related posts:
Alfa Romeo TZ3 Stradale
Aston Martin is coolest
Alfa Romeo TZ3 Corsa
Monday, May 9, 2011
Land Rover may already be working on a diesel-electric hybrid powertrain, but the company’s South African subsidiary has gone one step further by producing an all-electric Defender in collaboration with lithium-ion battery pack specialists Axeon and Baker Performance Products.
Based on a 110 High Capacity Pick Up, the Electric Defender Game Viewer Concept Vehicle is designed for use in game parks where the ability to run quietly has obvious benefits.
The custom-made 300 volt 27 kW/hr battery pack fits entirely within the engine bay, so that ground clearance is unaffected and the electrical systems are kept dry when the Defender is wading. It powers an air-cooled AC induction motor that produces 79 bhp (59 kW / 80 PS), with a regenerative capacity of 13 bhp (10 kW / 14 PS), and 330 Nm (243 lb/ft) of torque.
It’s said that three typical game drives can be completed on a single charge, which equates to a range of around 50 miles (80 km) plus 12 miles (20 km) in reserve. Recharging is via the mains or a solar adapter.
For the moment the Electric Defender is just a one-off, although there could be other applications where the technology proves to be useful.
Related post:
Land Rover Range_e
Land Rover may already be working on a diesel-electric hybrid powertrain, but the company’s South African subsidiary has gone one step further by producing an all-electric Defender in collaboration with lithium-ion battery pack specialists Axeon and Baker Performance Products.
Based on a 110 High Capacity Pick Up, the Electric Defender Game Viewer Concept Vehicle is designed for use in game parks where the ability to run quietly has obvious benefits.
The custom-made 300 volt 27 kW/hr battery pack fits entirely within the engine bay, so that ground clearance is unaffected and the electrical systems are kept dry when the Defender is wading. It powers an air-cooled AC induction motor that produces 79 bhp (59 kW / 80 PS), with a regenerative capacity of 13 bhp (10 kW / 14 PS), and 330 Nm (243 lb/ft) of torque.
It’s said that three typical game drives can be completed on a single charge, which equates to a range of around 50 miles (80 km) plus 12 miles (20 km) in reserve. Recharging is via the mains or a solar adapter.
For the moment the Electric Defender is just a one-off, although there could be other applications where the technology proves to be useful.
Related post:
Land Rover Range_e
Friday, May 6, 2011
Jaguar has announced that its C-X75 supercar is to make it to production, with the project getting assistance from the Williams F1 team.
Although the micro-turbine of the original 2010 Paris Motor Show concept will be swapped for a small capacity internal combustion engine, the C-X75 remains a hybrid thanks to a pair of electric motors powering an axle each.
That arrangement is claimed to offer an astonishing combination of performance and efficiency.
The targets are a 0-60 mph (96 km/h) acceleration time of under three seconds and a top speed of over 200 mph (321 km/h), combined with CO2 emissions of less than 99 g/km. What’s more, the C-X75 should be able to operate as a pure electric vehicle for at least 30 miles (50 kilometres).
Williams F1’s involvement is to focus on aerodynamics, hybrid technologies and the use of carbon composites for the Jaguar’s chassis.
Only 250 examples of the Jaguar C-X75 are going to be built, and prices will be between £700,000 and £900,000 depending on local taxes. That’s around €800,400 - €1,030,000 or US$1,146,000 - US$1,473,400 based on today’s exchange rates.
Jaguar has announced that its C-X75 supercar is to make it to production, with the project getting assistance from the Williams F1 team.
Although the micro-turbine of the original 2010 Paris Motor Show concept will be swapped for a small capacity internal combustion engine, the C-X75 remains a hybrid thanks to a pair of electric motors powering an axle each.
That arrangement is claimed to offer an astonishing combination of performance and efficiency.
The targets are a 0-60 mph (96 km/h) acceleration time of under three seconds and a top speed of over 200 mph (321 km/h), combined with CO2 emissions of less than 99 g/km. What’s more, the C-X75 should be able to operate as a pure electric vehicle for at least 30 miles (50 kilometres).
Williams F1’s involvement is to focus on aerodynamics, hybrid technologies and the use of carbon composites for the Jaguar’s chassis.
Only 250 examples of the Jaguar C-X75 are going to be built, and prices will be between £700,000 and £900,000 depending on local taxes. That’s around €800,400 - €1,030,000 or US$1,146,000 - US$1,473,400 based on today’s exchange rates.
Saturday, April 9, 2011
Mercedes-Benz looks to be taking its A-Class in a totally different direction. The Concept A-Class, which will be unveiled at this month’s Auto Shanghai show, eschews the tall, short mini-MPV shape of the previous two A-Class generations for an altogether more dynamic appearance.
A low stance and long bonnet completely change the proportions, while the complex swage lines along the side and the front-end styling echo the CLS. It certainly looks very different, and the more conventional body could allow the entry level Mercedes-Benz to take sales from its BMW 1 Series and Audi A3 competitors.
As with most show cars, there are plenty of features on the Concept A-Class that are unlikely to make it into production. The dashboard treatment is a prime example, as it has a stretchable and translucent textile covering, which apparently ‘enables the bionic, cellular structure of the component to remain visible’…
The Concept A-Class retains a front-wheel drive configuration, with power coming from a BlueEFFICIENCY four-cylinder petrol engine producing 207 bhp (155 kW / 210 PS). No performance, economy or emissions figures have been released, but Mercedes-Benz is claiming that a combination of turbocharging and direct injection will benefit all three measures. Drive is via a new dual-clutch transmission.
Mercedes-Benz looks to be taking its A-Class in a totally different direction. The Concept A-Class, which will be unveiled at this month’s Auto Shanghai show, eschews the tall, short mini-MPV shape of the previous two A-Class generations for an altogether more dynamic appearance.
A low stance and long bonnet completely change the proportions, while the complex swage lines along the side and the front-end styling echo the CLS. It certainly looks very different, and the more conventional body could allow the entry level Mercedes-Benz to take sales from its BMW 1 Series and Audi A3 competitors.
As with most show cars, there are plenty of features on the Concept A-Class that are unlikely to make it into production. The dashboard treatment is a prime example, as it has a stretchable and translucent textile covering, which apparently ‘enables the bionic, cellular structure of the component to remain visible’…
The Concept A-Class retains a front-wheel drive configuration, with power coming from a BlueEFFICIENCY four-cylinder petrol engine producing 207 bhp (155 kW / 210 PS). No performance, economy or emissions figures have been released, but Mercedes-Benz is claiming that a combination of turbocharging and direct injection will benefit all three measures. Drive is via a new dual-clutch transmission.
Monday, April 4, 2011
BMW has revealed the 2012 M5 - albeit in ‘concept’ form - ahead of its debut at this month’s Shanghai motor show.
Performance figures have yet to be released, although BMW has confirmed that the V10 engine of the previous generation E60 M5 has been ditched in favour of a twin-turbo V8 for the new F10 model.
This is expected to be an adapted version of the 4.4 litre unit already seen in the X5 M and X6 M, and BMW is promising increased power combined with a 25% reduction in fuel consumption and emissions.
Drive to the rear wheels will be via a seven-speed M double-clutch transmission, while a specially calibrated active differential has been engineered to minimise wheel spin and maximise traction.
Visually, all of the usual M5 styling cues are present. These include subtly widened wheel arches housing bespoke 20” forged alloy wheels, neat front wing gills and reworked front and rear aprons that are designed to aid both cooling and aerodynamics.
The interior remains a mystery for now though. The blacked-out glass of the concept suggests that it’s probably still work in progress.
Related post:
Alpina B5 UK sales start
Subscribe to:
Posts (Atom)
